Arctic Cat
Wear Rod Application Chart

The finest wear rods and... we can prove it!

order

To prevent cross-threading, rotate the nut counter-clockwise until you feel the end of the nut's thread fall over the end thread of the bolt. Then, turn clockwise to tighten.

Do not over tighten nuts!  Tighten only until firmly snug.  This is especially important when working with plastic skis.  They always have a cushioned feel to them, unlike steel skis which provide a dead stop to the nut. We use 5/16" x 18 bolts because these are all that is necessary - strength-wise. Having more than one bolt only helps keep the host bar straight. Also, this allows the easiest installation without any need to drill the skis or use a hammer. It is not the size of the bolts, but the number and location that is important. Easy installation


Arctic Cat wear rod drawings     Front 90 degree bend  - Not!     Easy installation     Product enhancements

For 2001 and older Artic Cat Application Charts - Click Here

 

To specify Triple Point Carbide models, replace the Good 'n Ugly prefix C or CH with TP

For example: C-B13 becomes TP-B13 or CH6-B12 becomes TP6-B12

Pricing Info 4" 6" 8"
Triple Point Carbide NA TP6
TP8
Good 'n Ugly - single carbide

C

CH6

CH8

Model numbers shown below are for Good n Ugly single carbides only.

Arctic Cat 2002 4" 6" 8"
4 Stroke - All C-B12 CH6-B12 CH8-B12
Thundercat C-B11-B CH6-B11-B CH8-B11-B
ZRT 600 C-B11-B CH6-B11-B CH8-B11-B
ZR - All C-B13 CH6-B13 CH8-B13
ZL - All C-B11-B CH6-B11-B CH8-B11-B
Z - All C-B12 CH6-B12 CH8-B12
Mtn Cat - All C-B11-B CH6-B11-B CH8-B11-B
Pantera 600, 800 C-B11-B CH6-B11-B CH8-B11-B
Pantera 550 C-B12 CH6-B12 CH8-B12
Panther - All C-B12 CH6-B12 CH8-B12

Bearcat WT

C-B11-B CH6-B11-B CH8-B11-B
seperator
Arctic Cat 2003
Firecat - All C-B13 CH6-B13 CH8-B13
ZR - All C-B13 CH6-B13 CH8-B13
ZL - All C-B11-B CH6-B11-B CH8-B11-B
Z - All C-B12 CH6-B12 CH8-B12
Mtn Cat - All C-B11-B CH6-B11-B CH8-B11-B
4-Stroke C-B12 CH6-B12 CH8-B12
Pantera 600, 800 C-B11-B CH6-B11-B CH8-B11-B
Pantera 550, 570 esr C-B12 CH6-B12 CH8-B12

Bearcat WT

C-B11-B CH6-B11-B CH8-B11-B
seperator
Arctic Cat 2004
Firecat - All C-B13 CH6-B13 CH8-B13
Sabercat - All C-B13 CH6-B13 CH8-B13
ZR - All C-B13 CH6-B13 CH8-B13
Mtn Cat - All C-B11-B CH6-B11-B CH8-B11-B
T 660 Turbo Touring, Touring C-B11-B CH6-B11-B CH8-B11-B

T 660 Turbo

C-B12 CH6-B12 CH8-B12
Z - All C-B12 CH6-B12 CH8-B12
Pantera - All C-B11-B CH6-B11-B CH8-B11-B
Panther - All C-B12 CH6-B12 CH8-B12
Bearcat WT C-B11-B CH6-B11-B CH8-B11-B
seperator
For maximum function, if your skis only have 3 bolt holes you need to drill a 4th hole.
If you have another A.C. sled with plastic skis order the same bolt pattern, B11-B or B13
Arctic Cat 2005
Firecat - All C-B13 CH6-B13 CH8-B13
Sabercat - All C-B13 CH6-B13 CH8-B13
ZR - All C-B13 CH6-B13 CH8-B13
Z - All C-B12 CH6-B12 CH8-B12
Kingcat - All C-B11-B CH6-B11-B CH8-B11-B
M 7, 6, 5 - All C-B13 CH6-B13 CH8-B13
T 660 - All C-B13 CH6-B13 CH8-B13
Pantera 600 EFI C-B13 CH6-B13 CH8-B13
Pantera 550 CB11-B CH6-B11-B CH8-B11-B
Panther 570 + 370 C-B12 CH6-B12 CH8-B12

Bearcat -All

C-B11-B CH6-B11-B CH8-B11-B

 

Arctic Cat wear rod drawings    Front 90 degree bend  - Not!     Easy installation     Product enhancements

order

Home  |  Arctic Cat Wear Rod Drawings  | Ski Savers Chart  Trail Grabbers Chart
Wear Rod Main Page  |  Site Map


Bergstrom Skegs

Contact Us

Copyright © 1999-2016 Bergstrom Skegs, Inc.
All rights reserved.