Polaris |
|
 |
Polaris |
|
|
|
Do not over tighten nuts! Tighten only until firmly snug. This is especially important when working with plastic skis. They always have a cushioned feel to them, unlike steel skis which provide a dead stop to the nut. We use 5/16" x 18 bolts because these are all that is necessary - strength-wise. Having more than one bolt only helps keep the host bar straight. Also, this allows the easiest installation without any need to drill the skis or use a hammer. It is not the size of the bolts, but the number and location that is important. Easy installation
To prevent cross-threading, rotate the nut counter-clockwise until you feel the end of the nut's thread fall over the end thread of the bolt. Then, turn clockwise to tighten.
 |
NEW! Bergstrom Skegs' 7/16" diameter hardsurfaced wear rods. These 7/16" hardsurfaced wear rods will outwear almost two sets of our standard 3/8" hardsurfaced wear rods. Also, they will lift your plastic skis higher off the ground for more protection. | |
|
|
||
| Pricing (per pair) | $22.00 | $48.00 | $57.00 | $69.00 | $82.00 | $100.00 |
| Model/Year | Hard Surfaced | Type 1 | Type 2 | Type 3 | Type 4 | Type 5 |
| All Models 71-85 | H02 | C-H02 | X | X | X | X |
| All Indy's 86-87 (Except below) | H03 | C-H03 | X | X | X | X |
| Sport 87 | H04 | C-H04 | C6-H04 | CH6-H04 | CH8-H04 | CH10-H04 |
| All Indy's 88-04 (steel skis) | H04 | C-H04 | C6-H04 | CH6-H04 | CH8-H04 | CH10-H04 |
| Ultra Lite (SLP) | H04P | C-H04P | C6-H04P | CH6-H04P | CH8-H04P | CH10-H04P |
| All Plastic Skis (except below) | H04P | C-H04P | C6-H04P | CH6-H04P | CH8-H04P | CH10-H04P |
| Sidehiller 2 03-04 | HO6 | C-H06P | C6-H06P | CH6-H06P | CH8-H06P | |
| "Easy Steer" Replacement Ski | H05 | C-H05 | C6-H05 | X | X | X |
| RMK 600 / 700 /
800 03-04 (Accu-Trak) (Except Sidehiller 2 skis) Accu-Track wear rods are only a temporary and superficial fix for darting because they do not address the causes of darting. We suggest using a H04P rod with 3/8" Ski Savers. The back three bolts do line up. To get proper wear pattern, add a 3/16" to 1/4" shim to the bottom back of the rubber stop. |
H04P | C-H04P | C6-H04P | CH6-H04P | CH8-H04P | CH10-H04P |
| SKS 700 / 800
03-04 (Accu-Trak) (Except Sidehiller 2 skis) Accu-Track wear rods are only a temporary and superficial fix for darting because they do not address the causes of darting. We suggest using a H04P rod with 3/8" Ski Savers. The back three bolts do line up. To get proper wear pattern, add a 3/16" to 1/4" shim to the bottom back of the rubber stop. |
H04P | C-H04P | C6-H04P | CH6-H04P | CH8-H04P | CH10-H04P |
| Pricing (per pair) | $22.00 | $48.00 | $57.00 | $69.00 | $82.00 | $100.00 |
Home |
Polaris Wear Rod Drawings | Ski Savers Chart |
Trail Grabbers Chart
Wear Rod Main Page | Site Map
1158 Power Road, Rockford, Illinois 61115
Phone: 815-654-2950
E-mail: beskegs@inwave.com
Copyright © 1999-2007 Bergstrom Skegs, Inc.
All
rights reserved.
Website design and graphics by Daniel Design
Group
